====== WLAN ======
:!: die hier vorgestellten Konfig-Dateien enthalten noch keine Sicherheitsparameter (z.B. WLAN-Verschlüsselung/Authentifikation bei HostAPd), sie dienen lediglich zum schnellen Test
===== intern =====
in Kernel 4.4.70 ist der Wlan-Code vorhanden, muss aber separat aktiviert werden
[[https://github.com/BPI-SINOVOIP/BPI-R2-bsp/tree/master/vendor/mediatek/connectivity|GitHub]]
[[http://forum.banana-pi.org/t/2-4ghz-and-5-6ghz-wifi-working-fine/3844/32|Forum]]
[[https://github.com/BPI-SINOVOIP/BPI-R2-bsp/commit/6b9512b853b1efc66109a41a0108579dcc9e054c|Patch]] [[https://github.com/BPI-SINOVOIP/BPI-R2-bsp/commit/219be3221aadb2d316557df8064bb231ca46ed51|Patch #2]]
:!: wpasupplicant muss deinstalliert, hostapd+dnsmasq installiert werden:
apt-get remove wpasupplicant
apt-get install hostapd dnsmasq
hostapd.conf:
hw_mode=g
interface=ap0
driver=nl80211
channel=1
auth_algs=1
ssid=test
{{ :bpi-r2:wmt_soc.cfg | cfg nach /system/etc/firmware/}}
{{ :bpi-r2:r2_wifi_helper.zip | Hilfsprogramme für die nächsten Schritte (entpacken nach /usr/bin)}} und {{ :bpi-r2:r2-firmware.zip | Firmware (entpacken /etc/firmware/)}} von [[https://github.com/BPI-SINOVOIP/BPI-R2-bsp/tree/master/vendor/mediatek/connectivity|hier]]
- wmt_loader
- stp_uart_launcher -p /etc/firmware &
- Treibermodul laden (wenn als Modul 5.4+ compiliert): modprobe wlan_gen2
- ( echo 0 >/dev/wmtWifi (zurücksetzen/initialisieren) )
- echo A >/dev/wmtWifi (AP-Modus aktivieren)
beim letzten Schritt wird das AP-Gerät (Accesspoint) erzeugt, welches dann von hostapd genutzt wird
[14:14] root@bpi-r2:~# ifconfig -a|grep Link
ap0 Link encap:Ethernet HWaddr 02:08:22:68:39:ff
bond0 Link encap:Ethernet HWaddr e2:7c:e0:71:31:c1
eth0 Link encap:Ethernet HWaddr 08:00:00:00:00:00
inet6 addr: fe80::a00:ff:fe00:0/64 Scope:Link
eth1 Link encap:Ethernet HWaddr 08:00:00:00:00:01
inet6 addr: fe80::a00:ff:fe00:1/64 Scope:Link
lo Link encap:Local Loopback
sit0 Link encap:IPv6-in-IPv4
tunl0 Link encap:IPIP Tunnel HWaddr
wlan1 Link encap:Ethernet HWaddr 00:08:22:68:39:ff
hostapd starten
hostapd -dd /etc/hostapd/hostapd.conf
nun kann mit der Schnittstelle weitergearbeitet werden:
ip addr add 192.168.10.1/24 dev ap0
#ip link set dev ap0 up
service dnsmasq start
{{ :bpi-r2:hostapd.conf |}}
{{ :bpi-r2:wifi_enable.sh |altes Shell-Script für das Starten}}
{{ :bpi-r2:wifi.sh |}}
==== Kernel 4.14 ====
Code vom Kernel 4.4.70 habe ich in [[https://github.com/frank-w/BPI-R2-4.14/tree/wifi_mt6625l|mein github-repo]] eingebunden.
Diskussion hier (EN): [[http://forum.banana-pi.org/t/r2-internal-wifi-bt-mt6625l-kernel-4-14-x-4-15/4307|forum]]
==== bekannte Probleme ====
=== Zufallszahlen ===
direkt nach dem (Re-)boot ist der Zufallszahlengenerator noch nicht ausreichend gefüllt, so dass Verbindungversuche abgelehnt werden, bis dieser gefüllt ist.
in der hostapd-log sieht das so aus:
random: Cannot read from /dev/random: Resource temporarily unavailable
random: Got 0/14 bytes from /dev/random
random: Only 6/20 bytes of strong random data available from /dev/random
random: Not enough entropy pool available for secure operations
WPA: Not enough entropy in random pool to proceed - reject first 4-way handshake
...
WPA: Reject 4-way handshake to collect more entropy for random number generation
random: Mark internal entropy pool to be ready (count=1/2)
...
random: Cannot read from /dev/random: Resource temporarily unavailable
random: Got 0/14 bytes from /dev/random
random: Only 6/20 bytes of strong random data available from /dev/random
random: Allow operation to proceed based on internal entropy
http://forum.banana-pi.org/t/bpi-r2-new-image-release-ubuntu-16-04-v1-3-2018-3-30/5293/25
apt-get install rng-tools
echo 'HRNGDEVICE=/dev/urandom' >> /etc/default/rng-tools
===== extern =====
==== MT76 ====
FIXME
[[https://de.aliexpress.com/item/MTK-MT7612E-2x2-802-11ac-b-g-n-Enterprise-867Mbps-MiniPCIE-NIC-PCBA-ODM-OEM/32817460933.html|mt7612e auf AliExpress]]
=== 4.4.70 ===
[[http://forum.banana-pi.org/t/need-help-porting-mt76-driver-to-r2-kernel/3954/32|forum]]
git clone https://github.com/BPI-SINOVOIP/BPI-R2-bsp.git bpi_r2_mt76
cd bpi_r2_mt76/
cd linux-mt/drivers/net/wireless/mediatek
git clone https://github.com/dfiloni/mt76.git
cd ../../../.. #bpi_r2_mt76/linux-mt/
patch -p1 < drivers/net/wireless/mediatek/mt76/kernel-patches/0001-add-basic-register-field-manipulation-macros.patch
nano drivers/net/wireless/mediatek/Makefile
#add: obj-$(CONFIG_MT76) += mt76/
nano drivers/net/wireless/mediatek/Kconfig
#add before endif: before endif # WL_MEDIATEK: source "drivers/net/wireless/mediatek/mt76/Kconfig"
cd ..
./build.sh => 4
#networking support => wireless => Generic IEEE 802.11 Networking Stack (mac80211)
#Device Drivers => Network device support => Wireless LAN => [*] Mediatek Wireless LAN support => MediaTek MT76x2 802.11ac chips support
./build.sh => 1
cp SD/BPI-BOOT/bananapi/bpi-r2/linux/uImage /media/$USER/BPI-BOOT/bananapi/bpi-r2/linux/uImage
sudo cp -r SD/BPI-ROOT/lib/modules /media/$USER/BPI-ROOT/lib/
sudo cp linux-mt/drivers/net/wireless/mediatek/mt76/firmware/* /media/$USER/BPI-ROOT/lib/firmware/
#scp linux-mt/drivers/net/wireless/mediatek/mt76/firmware/* root@192.168.0.10:/lib/firmware/
sync
=== 4.14 ===
Kernel 4.14+ (in Arbeit...):
bei folgendem Fehler (dmesg):
mt76x2e: probe of 0000:01:00.0 failed with error -2
muss Firmware-Paket installiert werden:
apt-get install firmware-misc-nonfree
falls das abbricht muss in der /etc/apt/sources.list "non-free" hinter "main" ergänzt werden und "apt update" ausgeführt werden
{{ :bpi-r2:pcie.patch |PCIe-patch}} importieren, wenn noch nicht geschehen
patch -p1 < pcie.patch
cd drivers/net/wireless/mediatek/
git clone https://github.com/openwrt/mt76.git
* in der mt76/mt7603.h fehlt "#include "
* in der mt76/mac80211.c fehlt "#include "
* im Makefile fehlen "CFLAGS_trace.o := -I$(src)" und "CFLAGS_mt76x2_trace.o := -I$(src)"
* und halt in drivers/net/wireless/mediatek/Makefile obj-$(CONFIG_MT76) += mt76/
und drivers/net/wireless/mediatek/Kconfig source "drivers/net/wireless/mediatek/mt76/Kconfig"
einbinden
{{ :bpi-r2:mt76_4.14.tar.gz | fertiger Treiber für mt76x2 + mt76x3}} nach drivers/net/wireless/mediatek/ entpacken
folgende module im kernel aktivieren:
CONFIG_MAC80211=m
CONFIG_CFG80211=m
CONFIG_MT76=m
#pcie
CONFIG_PCIEPORTBUS=y
CONFIG_PCIE_MEDIATEK=y
CONFIG_PHY_MTK_TPHY=y
die firmware kopieren
sudo cp drivers/net/wireless/mediatek/mt76/firmware/* /media/$USER/BPI-ROOT/lib/firmware/
=== einrichten ===
[10:50] root@bpi-r2:~# ifconfig -a |grep wlan
wlan1 Link encap:Ethernet HWaddr f8:62:aa:50:12:1d <<<
Wenn die wlan-Nummer größer 1, entsprechend anpassen
nano /etc/udev/rules.d/70-persistent-net.rules
/etc/hostapd/hostapd_wlan1.conf (ggf. interface ändern):
interface=wlan1
#interface=ap0
driver=nl80211
ssid=r2_AP
hw_mode=g
channel=1
#macaddr_acl=0
auth_algs=1
#ignore_broadcast_ssid=0
#wpa=2
#wmm_enabled=1
#wpa_passphrase=12345678
#wpa_key_mgmt=WPA-PSK
#wpa_pairwise=TKIP
#rsn_pairwise=CCMP
{{ :bpi-r2:hostapd_wlan1.conf | /etc/hostapd/hostapd_wlan1.conf }}
hostapd starten (Debugmode):
hostapd -dd /etc/hostapd/hostapd.conf
IP-Adresse setzen:
ip addr add 192.168.11.1/24 dev wlan1
/etc/dnsmasq.conf (zeile aktivieren = # am Anfang entfernen)
conf-dir=/etc/dnsmasq.d
/etc/dnsmasq.d/interfaces.conf
#interface=eth0
interface=wlan0
#interface=eth1
interface=ap0
# DHCP-Server nicht aktiv für Interface
#no-dhcp-interface=ppp0
no-dhcp-interface=eth0
no-dhcp-interface=eth1
#dhcp-authoritative
dhcp-range=ap0,192.168.10.100,192.168.10.150,255.255.255.0,48h
dhcp-option=ap0,3,192.168.10.1
dhcp-range=wlan1,192.168.11.100,192.168.11.150,255.255.255.0,48h
dhcp-option=wlan1,3,192.168.11.1
{{ :bpi-r2:interfaces.conf | /etc/dnsmasq.d/interfaces.conf }}
===== HostAPd =====
{{ :bpi-r2:hostapd.conf | /etc/hostapd/hostapd.conf}}
{{ :bpi-r2:hostapd_wlan1.conf | /etc/hostapd/hostapd_wlan1.conf }}
Vif: https://github.com/openwrt/mt76/issues/433
==== 5GHz ====
[[https://www.tobias-bauer.de/hostapd-auf-5-ghz.html|5GHz]]
apt-get install iw wireless-regdb crda
=== country code ===
den Country-Code (regulary domain) zu setzen kann bisschen tricky sein
iw reg set ISO_3166-1_alpha-2
iw reg set DE
iw reg get
falsche Ausgabe:
global
country 00: DFS-UNSET
richtig:
global
country DE: DFS-ETSI
cfg80211 als Modul (5.4,5.10,5.12+ wegen mt6625 treiber):
$ sudo nano /etc/modprobe.d/cfg80211.conf
options cfg80211 ieee80211_regdom=DE
ggf. manuell laden
modprobe cfg80211 ieee80211_regdom=DE
evtl. probieren:
COUNTRY=DE crda
bricht bei mir aber mit "Failed to set regulatory domain: -7" ab, kann aber das 5GHz Band mit hostapd nutzen. Der letzte Schritt ist also nicht nötig
=== mögliche Frequenzen ===
iw list | grep MHz
=== Hostapd-Konfiguration ===
$ sudo nano /etc/hostapd/hostapd.conf
[...]
country_code=DE
ieee80211n=1
ieee80211d=1
hw_mode=a
channel=48
[...]
* https://raspberrypi.stackexchange.com/a/112048
* https://askubuntu.com/a/1276635
* https://github.com/openwrt/mt76/issues/433
===== IP-Konfiguration =====
IP-Adresse setzen:
ip addr add 192.168.10.1/24 dev ap0
ip addr add 192.168.11.1/24 dev wlan1
/etc/dnsmasq.conf (zeile aktivieren = # am Anfang entfernen)
conf-dir=/etc/dnsmasq.d
/etc/dnsmasq.d/interfaces.conf
#interface=eth0
interface=wlan0
#interface=eth1
interface=ap0
# DHCP-Server nicht aktiv für Interface
#no-dhcp-interface=ppp0
no-dhcp-interface=eth0
no-dhcp-interface=eth1
#dhcp-authoritative
dhcp-range=ap0,192.168.10.100,192.168.10.150,255.255.255.0,48h
dhcp-option=ap0,3,192.168.10.1
dhcp-range=wlan1,192.168.11.100,192.168.11.150,255.255.255.0,48h
dhcp-option=wlan1,3,192.168.11.1
{{ :bpi-r2:interfaces.conf | /etc/dnsmasq.d/interfaces.conf }}
==== Routing ====
nano /etc/sysctl.conf
#net.ipv4.ip_forward=1 und net.ipv6.conf.all.forwarding=1 aktivieren durch entfernen der Raute am Zeilenanfang
sysctl -p /etc/sysctl.conf
Voraussetzung ist, dass der Router (wenn es nicht der BPI-R2 selbst ist) das/die WLAN-Netz(e) auch kennt und weiß wohin er die Pakete schicken muss.
Die folgenden beiden Befehle müssen im (Debian-)Router ausgeführt werden, um die Routing-Tabelle entsprechend zu erweitern (gehen beim reboot verloren, wenn nicht beim Systemstart ausgeführt):
route add -net 192.168.10.0 netmask 255.255.255.0 gw 192.168.0.10
route add -net 192.168.11.0 netmask 255.255.255.0 gw 192.168.0.10
dabei ist 192.168.10.0 das Netz des 1. WLAN, 192.168.11.0 das Netz des 2. WLAN und 192.168.0.10 die LAN-IP des BPI-R2 (gleiches netz wie die LAN-IP des Routers)